@article {12_IEEEMWCL_Leal-SevillanoMontejo-GaraiRuiz-CruzEtAl_Low-LossEllipticalResponse,
	title = {Low-Loss Elliptical Response Filter at 100 GHz},
	journal = {Microwave and Wireless Components Letters, IEEE},
	volume = {22},
	number = {9},
	year = {2012},
	month = {September},
	pages = {459 -461},
	abstract = {The design, method of fabrication and experimental validation of a pseudo-elliptical four-poles asymmetric response filter at 100 GHz with 10\% of fractional bandwidth is presented. The designed filter is part of an image radar system and must fulfill stringent specifications. The proposed topology and method of fabrication improves the out of band rejection above the pass band in comparison with other classical structures, while keeping a low insertion loss level. A two-fold geometry for implementing a transmission zero is proposed, avoiding the excitation of the first higher order mode and easing the manufacturing without any tuning element. A low-cost milling process is used for the fabrication of the device. The final design fulfills the desired specifications and presents 0.6 dB of insertion loss level at 100 GHz. The excellent agreement between simulations and measurements at this frequency band in both, return loss and insertion loss, is pointed out.},
	keywords = {Asymmetric, band-pass filters, elliptic filters, extracted pole, Fabrication, fabrication method, filter, filtering theory, fractional bandwidth, frequency 100 GHz, higher order mode, image radar system, Insertion loss, loss 0.6 dB, Loss measurement, low insertion loss level, low loss, low-cost milling process, low-loss elliptical response filter, microwave filters, millimetre wave filters, Milling, out of band rejection, pseudo-elliptical four-poles asymmetric response filter, Radar, return loss, transmission zero, two-fold geometry, W-band},
	issn = {1531-1309},
	doi = {10.1109/LMWC.2012.2212237},
	url = {http://ieeexplore.ieee.org/xpls/abs_all.jsp?arnumber=6268297\&tag=1},
	author = {C A Leal-Sevillano and Montejo-Garai, J R and J A Ruiz-Cruz and Rebollar, J M}
}
@conference {04_IMS_LiuRuiz-CruzWangEtAl_extremelywidebandridge,
	title = {An extremely wideband ridge waveguide filter},
	booktitle = {2004 IEEE MTT-S International Microwave Symposium Digest},
	volume = {2},
	year = {2004},
	month = {June},
	pages = {615-618},
	abstract = {An extremely wideband ridge waveguide filter is presented. The fractional bandwidth of the filter can be greater than 115\%. An input and output transition from ridge waveguide to stripline and then to coax is also designed. The analysis is done with mode matching method and verified with Ansoft HFSS. For validation purpose, a test filter with pass band from 3 GHz to 9 GHz has been designed. The results by both mode matching method and Ansoft HFSS are presented. Excellent agreement is obtained. The test filter is designed using air filled ridge waveguide; however the same design procedure can be equally applied to other manufacturing techniques such as LTCC.},
	keywords = {air filled ridge waveguide, fractional bandwidth, mode matching, mode matching method, ridge waveguides, strip lines, stripline, waveguide filters 3 to 9 GHz, wideband ridge waveguide filter},
	issn = {0149-645X},
	doi = {10.1109/MWSYM.2004.1336059},
	url = {http://ieeexplore.ieee.org/iel5/9277/29472/01336059.pdf?tp=\&isnumber=\&arnumber=1336059},
	author = {Liu, Z M and J A Ruiz-Cruz and Wang,C and Zaki, K A}
}
